|
|
|
|
CRC 2.26
|
|
| Description: |
CRC 2.26
Improves electrical properties for higher voltage applications. High dielectric strength.
Pack Sizes Available
Jerry Can 20 litre [2009]
Aerosol 300 gm [2005]
Displaces moisture, seals out moisture, prevents corrosion, cleans, lubricates, penetrates.
Prevents 80% of all electrical failures. (Most electrical failures are caused by moisture or corrosion).
CRC 2.26 can prove to be the most valuable electrician's tool because of its many uses. This product provides a multiple inventory in a single container. 'A 6 in 1 product'.
1. A moisture eliminator - for wet equipment.
2. A moisture barrier to prevent trouble before it starts. The protective film seals out moisture.
3. A lubricant - 25-50 microns will give lubrication equivalent to a 10 weight motor oil. Contains no silicones.
4. A penetrant - frees rusted or corroded parts.
5. A protector against corrosion.
6. A cleaner - apply to a corroded area, let it penetrate, then repair it by rubbing with a light abrasive. The solvent system in 2.26 will degrease but naturally it is not as effective as Lectra-Clean.
CRC 2.26 is a stable, inert organic formula, especially prepared to prevent and repair electric failures due to moisture, corrosion, dirt or friction.
CRC 2.26 effectiveness is the result of the following properties:
A very low surface tension, high capillary action and strong affinity for metals, give it great penetrating and spreading powers (expected coverage 100-140m2/litre) Therefore the microscopic film will spread under any moisture, covering the total surface by penetrating into the finest pores and cracks. Penetration continues for 24 hours, which is important for complete moisture elimination. It will at the same time, release rusted and frozen parts.
The continuous molecular film is self-repairing and seals the surface against future moisture and corrosion.
The special corrosion protection properties result from a multiple, complex system of inhibitors dispersed in the non-volatile part of the product. Insulating film resists flow of corrosion current, passivation by bonding to active metal surface ions, elimination of electrolyte and corrosive media by a film barrier.
The volatile part of the CRC 2.26 (i.e. the solvents) offers cleaning action as a supplementary benefit and will evaporate after 4-6 hours.
The lubricity of the remaining film is excellent and offers precision lubrication where it is required.
The high dielectric strength of CRC 2.26 makes it ideal for high voltage applications. It does not increase electrical resistance but does restore electrical characteristics to their original value.
The time of protection of CRC 2.26 will vary with the environmental conditions and the best results will be obtained indoors. As it is a soft film which never dries, direct weathering exposure can limit the time of protection outdoors and would require repeated application. For direct prolonged outdoor protection of metals see also CRC Urethane Seal Coat and CRC Zinc-It.
Approvals
USDA Authorised for use in Federally inspected Meat and Poultry Plants.
MAF Approved (C14) Meat
MIL Specs: Mil - C-81309C Type 111; W-P-216B; O-W-1284B;
NSN 6850-00-874-5847
NSN 6850-98-106 4647 Aerosol
NSN 6850-98-106 2693 bulk
Conforms to Aust Defence Spec 1002-PX112
Certificate of inspection for use in NSW Coal Mines
Physical Properties
Flash Point; Flash Point Dry Film (Open Cup) 80°C; 235°C
Heat Resistance Film degradation begins at: 150°C
Distillation Range 76-365°C
Specific Gravity 0.8167 ± 0.02
Dielectric Strength 42,000 volts per ASTM #D.877
pH 6.0 to 7.0
Viscosity (20°C) 4cP
Lubrication (Falex) Up to 1750 lbs
Average film thickness 1 to 2 Microns
Expected coverage 1 to 2 Microns |
|
Asking price: No price is shown
|
|
|
 |
|
 |
|
|